hama 00179807 PHILIPS TVs Replacement Remote Control Manual

hama 00179807 PHILIPS TVs Replacement Remote Control Instruction Manual

Thank you for your decision for a Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference.

This remote control can by default control 90% models of PHILIPS brand, there´s no need to set it up. lf the remote doesn‘t work, please choose one of the setup method described in chapter 5.

The keys

1. Power TV ON/OFF – Indicator LED
2. Suspends play and stops on an image (DVD, BlueRay…)
3. Stop the disc (DVD, BlueRay … )
4. Play a disc (DVD, BlueRay … )
5. Goes backward (DVD, BlueRay … )
6. 3D Mode ON/OFF
7. Show the Electronic Program Guide (if supported by the TV)
8. Shift to TV
9. Input Signal Source
10. Record
11. Fast Forward (DVD, BlueRay … )
12. AMBILIGHT
13. Picture Size
14. Streaming app menu
15. Info
16. Options and Tools
17. HOME
18. Channel List
19. Use when watching TV to see what´s on other channels or to highlight/ select On-Screen options
20. Exit Menu
21. Return/Back Key
22. Channel +/-
23. Volume +/-
24. Use to select a variety of on-screen options
25. Numeric keys 0–9to enter channel numbers
26. Subtitle
27. Teletext ON/OFF
28. Turn your TV sound ON/OFF

Explanation of the Note and Warning symbol

Warning

This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

Package Contents

• Replacement Remote Control
• 2x AAA Batteries
• This operating instructions incl. Code List

Safety notes

• Do not use the remote control in moist or wet environments and avoid spraywater contact.
• Do not expose the remote control to heat sources or direct sunlight.
• Do not drop the remote control.
• Never open the remote control. It contains no user-serviceable parts.
• As with all electrical devices, keep the Universal remote control away from children.

Warning – Batteries

• When inserting batteries, note the correct polarity (+ and – markings) and insert the batteries accordingly. Failure to do so could result in the batteries leaking or exploding.
• Only use batteries (or rechargeable batteries) that match the specified type.
• Before you insert the batteries, clean the battery contacts and the polar contacts.
• Do not allow children to change batteries without supervision.
• Do not mix old and new batteries or batteries of a different type or make.
• Remove the batteries from products that are not being used for an extended period (unless these are being kept ready for an emergency).
• Do not short-circuit batteries.
• Do not charge batteries.
• Do not throw batteries in a fire.
• Keep batteries out of the reach of children.
• Never open, damage or swallow batteries or allow them to enter the environment. They can contain toxic, environmentally harmful heavy metals.
• Immediately remove and dispose of dead batteries from the product.
• Avoid storing, charging or using the device in extreme temperatures and extremely low atmospheric pressure (for example, at high altitudes).

Getting started – installing the Batteries

Note

• Use 2 AAA batteries
• Remove the battery cover from bottom of remote.
• Check the +/- polarity on the batteries and inside the compartment.
• Insert the batteries.
• Slide the battery holder back into the remote until the clips locate.

Setup

This remote control can by default control 90% models of PHILIPS brand, there´s no need to set it up. If it doesn‘t work, please choose one of the following setup methods 5.1 or 5.2.

INPUT CODE

CODE List:

001, 002, 003, 004, 005, 006, 007, 008, 009, 010, 011, 012, 013, 014, 015, 016, 017, 018, 019, 020, 021, 022, 023, 024, 025, 026, 027, 028, 029, 030, 031, 032, 033, 034, 035, 036, 037, 038, 039, 040, 041, 042

1. Press and hold the key [MUTE] and [POWER] until the LED will be lit, then release keys.
   
2. Enter the three codes from code List. When the code input is finished, the LED will turn off.
   
3. Please try to use the remote control. If it doesn‘t work well, please try other codes: [002], [003], [004] ..

Note

• If the code is invalid, the LED flashes twice and then lights up permanently. To exit the setup, please press [MUTE].

FAST SEARCH

1. Press and hold the key [MUTE] and [POWER] until the LED will be lit, then
   release keys.
   
2. Press the key [ CH+]. Each time you press, the remote will search once. When
   the code changes, you can test if [POWER], [VOL+], [0-9] keys work well. If ok ,please press [ MUTE] to save the code and exit.
3. If it doesn‘t work well, repeat the fast search by pressing [ CH+].

CODE INQUIRY

Use the following method to find out which code is currently set:

1. Press and hold [MUTE], then press [POWER] until the LED will be lit, then release keys.
2. Input [9].[9].[0] with number keys. The LED will flash twice and goes off.
3. Press the number key 1 for the 1st digit of the code. The LED will start to flash. Count the LED flashes. The number of flashes resemble the code‘s first digit. Repeat this procedure for the 2nd and 3rd digit of the code:
   2nd digit -> enter 2 -> count LED flashes
   3rd digit -> enter 3 -> count LED flashes
   If code number is [0] the LED will not flash.

Compatible Remote Control Model

Due to too many remote control models, we only List some of them below.
If your remote control is similar to the drawing, the replacement remote can control your TV.

Resetting to factory settings

Press and hold the [RETURN ] and [0] buttons for about 5 seconds until the status LED flashes three times and then goes out. The remote control is now successfully reset to the factory settings.

Note

• All keys with learnt codes or all copied keys, as well as all remote control settings will be deleted.

LEARN MODE

This remote control is equipped with a learning function. Thus, you could learn functions of your original remote to this remote control.

BEFORE STARTING LEARN MODE

• The batteries in the two remote controls have to be in good condition.
  Replace them if necessary.
• Place the remote controls with the infrared diodes so that they point towards each other.
• Where necessary adjust the height of both remotes so that infrared diodes are properly aligned.
• The distance between the remote controls should be about 3 cm.
  

Note

• Do not move the remote controls during the learning procedure.
• Ensure that the room is not lit by fluorescents tubes or low energy consumption lamps since such light sources could interfere with the copying.
• The 2 remote controls must be at least 1 meter away from any light source.
• During learning mode, if no key is selected for more than 15 seconds, the learning mode will exit automatically or if no other remote signal is received.
• Each function key will hold only one command. A new command to be learned will automatically replace the previous one.

ENTER LEARN MODE

1. Press and hold the [MUTE] and [VOL+] keys for approx. 5 seconds until the
   LED will be lit.
   
2. Enter the code [9] [8] [0], the LED will flash 2 times and then remain on.
3. The remote control is now ready to learn new commands.

LEARNING OF KEYS

1. Press and release the desired key on the original remote control which you want the command to be learned. The LED at your replacement remote will flash to confirm that the information has been received.
2. Then press and release the target key on the remote control you want learned.
3. If the LED flashes 3 times and then remain on, the command has been learned successfully. Repeat these steps to learn other key functions.
4. Press the [MUTE] and [VOL-] buttons to save all learnt functions and to exit the learning mode

Note

• While replacing the batteries, the remote control will keep the functions of the learned keys.

CLEARING OF LEARNED KEYS

CLEARING OF ONE LEARNED KEY

1. Press and hold [MUTE] and [VOL+] keys for 5 seconds until the LED will be lit.
   
2. Enter the code [9] [8] [1], the LED will flash 2 times and then remain on.
3. Press and release the desired key at the replacement remote control which you want to clear the learned command. If the LED flashes 3 times, the learned command has been cleared successfully.

CLEARING OF ALL LEARNED KEYS

1. Press and hold [MUTE] and [VOL+] keys for 5 seconds until the LED will be lit.
   
2. Enter the code [9] [8] [2], the LED will flash 2 times and then remain on.
3. Press and release the [OK] key at the replacement remote control. If the LED flashes 3 times, all commands have been cleared successfully.

EASY Mode

This remote control is equipped with an EASY Mode. Thus you could reduce the functionality of the remote control to its basic functions. It avoids that the TV Settings are changed by mistake.

During the EASY Mode you still could use following keys:

: Switch the TV On or Off
– / +:  Change the volume
Mute the TV

CH-/CH+:  Change the program
0-9:  Numeric keys for program selection/ direct page selection Teletext
TEXT:  Teletext ON / OFF
Use to select a variety of on screen options

GUIDE:  Show the Electronic Program Guide (if supported by the TV)
Select signal source
Exit Menu
TV:  Shift to TV

Enter EASY Mode

1. Press and hold [MUTE] and [VOL+] keys for 5 seconds until the LED will be lit.
   
2. Enter the code [9] [7] [0], the LED will flash two times and then remain on.
3. Press and release the [OK] key, if LED flash 3 times, you have entered the EASY Mode successfully.

Exit EASY Mode

1. Press and hold [MUTE] and [VOL+] for 5 seconds until the LED will be lit.
   
2. Enter the code [9] [7] [0], the LED will flash two times and then remain on.
3. Press and release the [EXIT] key, if LED flash 3 times, you have exit the EASY Mode.

Note

• While the EASY Mode is activated only the keys mentioned in chapter 7. will work. If one of these keys is pressed the LED will be lit until the key is released. If one key is pressed during the normal mode, the LED will flash.

Maintenance

• Do not mix new and used batteries for powering the remote control, as old batteries tend to leak and may cause power drain.
• Do not use corrosive or abrasive cleansers on your remote control.
• Keep the remote control dust free by wiping it with a soft, dry cloth.

Troubleshooting

• Q. My remote control does not work at all!
  A. Check your TV. If the TV main switch is turned off, your Remote cannot
  operate your TV.
  A. Check whether your batteries are inserted properly and are in the correct +/- position.
  A. If the batteries are low, replace the batteries.
• Q. My TV responds only to some of the commands.
  A. Try other codes until most keys work properly.
• Q. Some keys of the remote control do not work anymore?
  A. Maybe the EASY Mode had been activated. Deactivate the EASY Mode as explained in chapter 7.2.

Warranty Disclaimer

The manufacturer assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Recycling Information

Note on environmental protection:

After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies: Electric and electronic devices as well as batteries must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale.
Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices/Batteries, you are making an important contribution to protecting our environment.