OFA STREAMER

URC 7935

INTRODUCTION

Thank you for purchasing the One For All Streamer Remote. This remote is designed to be used to control streaming boxes such as an Apple TV or a Roku, while also controlling the Power and Input of your TV, as well as the Volume of your TV or Sound Bar / Audio Video Receiver. The remote also features handy shortcut macros for direct access to your favorite streaming apps. And the multi-colored LEDs behind the menu ring will help you to know which device you are controlling, make setup easier, and can even be customized to a color of your choice.

WARRANTY / GUARANTEE INFORMATION

Terms and Conditions for “100% Guaranteed To Work” policy, and the separate 1 Year Limited Warranty against defects in material and workmanship can be found at www.oneforall.com/ remote guarantee, or you may request hard copies by calling 855-716-2573, or via mail to UEI Technical Support Service, Suite 301, 26250 Euclid Ave., Euclid, OH 44132. Please include your full name, product information, and contact information in your request communication.

LEGAL NOTICES

FCC STATEMENT:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. www.oneforall.com

Customer Support:

855-716-2573 (toll-free)
OFA warranty/terms & conditions: 855-569-6595 (toll free) www.oneforall.com Imported into the US by:
Universal Electronics Inc.
UEI Technical Support Services,
Suite 301 26250 Euclid Ave.
Euclid, OH 44132
One For All is a registered trademark of UEI Made in China
712886 RDN1030920 Eng

PREPARE YOUR REMOTE FOR INSTALLATION

KEY DESCRIPTIONS

SETUP

If you want to control a Roku TV branded TCL, RCA, Hisense, Sharp, Sanyo, or Insignia, please refer to section D ­ Setting Up a Roku TV
The OFA Streamer remote is pre-programmed to control a Roku streaming box, just insert batteries and it will work directly. However it can also be programmed to control another brand of streamer as well as the Volume, Mute, Input, and Power of your TV, or if required, the Volume and Mute of your Sound Bar. You can set up these devices on your remote as follows:

A SIMPLE SET

If the brand of your device is shown below, you can use the simplest system described in this section, please locate the brand of your device and note the key associated with it.
TV

STREAMER BOX

DIGITAL

SOUNDBAR / AUDIO RECEIVER

To set up your device:

1. Turn on your device (not on standby) and point the OFA remote towards it. If you are setting up a Streaming device, make sure a movie or TV show is playing.
2. To set up:
   2a TV Hold down TV POWER and BACK keys at the same time until the yellow LED under the ring blinks twice.
   2b STREAMER / DIGITAL MEDIA BOX Hold down STREAMER POWER and HOME at the same time until the red LED under the ring blinks twice
   2c AUDIO RECEIVER, SOUNDBAR Hold down VOLUME + and VOLUME – at the same time until the Green LED under the ring blinks twice.
3. Hold down the key for your brand and device as listed left – e.g. 6 for Replay ( ) for a
   

   TV

   STREAMER BOX

   SOUNDBAR / AUDIO RECEIVER

4. For TV the remote will send the Power key every 3 seconds, for a streaming box the remote will send the Play/Pause function, and for an AV Receiver or Sound Bar, the remote will send Mute until your device Mutes volume.
5. As soon as your device reacts by turning off (TV) Pausing (Streaming box) or Muting (Audio device), release the key.
6. The LED will blink twice in green and the remote should now operate your device.

• If you find one or more keys do not work as you expect, start again at step 2 – the remote
  will start with the next code in the memory.

B – SETUP BY CODE

If the brand of your device is not listed in the simplest feature, you can set it up by trying codes individually. To do this firstly locate your brand in the Code List. Brands a listed by device type; TV, Streamer, or Audio (Receiver or Soundbar).

Each code consists of 5 digits, which can be entered by using the following keys to represent the digits 1-6:

1. Turn on your device (not on standby) and point the OFA remote towards it.
2. To set up:
   2a TV Hold down TV POWER and BACK keys at the same time until the yellow LED under the ring blinks twice.
   2b STREAMER / DIGITAL MEDIA BOX Hold down STREAMER POWER and HOME at the same time until the red LED under the ring blinks twice
   2c AUDIO RECEIVER, SOUNDBAR Hold down VOLUME + and VOLUME – at the same time until the Green LED under the ring blinks twice.
3. Enter the first 5 digit code listed for your brand (e.g. 11565 for Zenith TV).
   
4. The green LED will blink twice.
5. Now aim the remote towards your device and press the Power (or Mute*) key.
6. If the device turns off (or mutes*), your remote is ready to use. If not, repeat steps 2-5 with the next code in the list.

• If you are setting up an Audio Video Receiver or Sound Bar, please try the Mute key during step 5.

After SimpleSet or Code Setup
Your One For All remote can operate on up to three devices. Most keys will control your streaming box, but you can control some functions of your TV and Sound Bar or Audio Video Receiver If you set up a TV, the Volume Up, Down, Mute, TV Power, and TV Input keys will then control your TV. The menu ring will light up in yellow to show you are controlling the TV.
If you then also set up an Audio Device such as a Sound Bar or Audio Video Receiver, the remote will then control the Volume Up, Down, and Mute of that device. The menu ring will light up in green to show you are controlling the Audio Device.
Input Shaft
As the TV Input key is intended to select the input on your TV and most TVs use a menu to select from a list of inputs, when the TV Input key is pressed and a TV is set up, the Menu Up, Down, Left, Right and OK keys temporarily control the TV. If the OK key is pressed, or no key is pressed for ten seconds, these keys will revert to controlling your streamer.

C – LEARNING

Your One For All remote control can learn any function from any other working remote control. This is a quick and easy one-time setup that allows controlling any infrared-controlled device you have in your living room. You can even combine multiple devices in one easy-to-use remote control – for example, you could teach the volume keys to control your Sound Bar, the TV Power and Input keys to control your TV, and the rest of the keys to controlling a Streaming box.
Or you could teach the Channel Up and Down keys to control your TV.
To do this, firstly make sure you have all your original remote controls to hand, and that they

1. Hold down TV Power and Mute until the red LED blinks twice.
2. Press and release the key you want to learn a function onto (for example the Channel Up key) – The red LED will blink once and go out.
3. Press and release* the corresponding key on the original remote, for example, Channel Up.
4. The LED will blink green twice to indicate the key has been learned correctly.
5. Repeat steps 2 and 3 for each key you want to learn – remember you can learn from multiple remotes, but only one function per key.
6. When you learned all the functions you require, press and hold the TV Power key until the green LED blinks four times.

Hints:

• If the red LED shows one long blink at step 4, the function was not learned correctly, please try again from step 2.
• If you find one or more keys don’t work properly after set up, you can re-enter the learning mode at any time by repeating the procedure from step 1.
• To delete a learned function, hold down Streamer Power and Mute until the red LED blinks twice, and press the key to delete twice.
• TV If one or more of your original remotes aren’t working, you can still set up the One For All remote by SimpleSet (B) or Code Set-Up (C).
• After Learning, the default color of the Menu Ring LED is red. If you would like to change this, see “Choose Color”.*

*Some remotes send commands differently. If you find a function that cannot be learned, try holding down the key on the original remote instead of pressing and releasing it.

D – SETTING UP A ROKU TV

If you want to set up the remote to control a TCL Roku TV (this may also work for some models of RCA and Hisense)

1. Hold down STB POWER and HOME at the same time until the red LED blinks twice
2. Press the BACK key 5 times
3. The LED will blink green twice and the remote should now work on your Roku TV.

To set up a Hisense, RCA, Sharp, or Sanyo Roku TV:

1. Hold down STB POWER and HOME at the same time until the red LED blinks twice
2. Press the HOME key 5 times
3. The LED will blink green twice and the remote should now work on your Roku TV.

To set up an Insignia Roku TV

1. Hold down STB POWER and HOME at the same time until the red LED blinks twice
2. Press the REPLAY key 5 times
3. The LED will blink green twice and the remote should now work on your Roku TV.

MULTI-COLORED RING

The ring around the menu directional keys lights up in a number of different colors. During programming, the colors will guide you through the setup process, and after you have set up your devices they will indicate which device you are controlling.
When controlling the TV, the ring will light up yellow, and when controlling a Soundbar or Audio/ Video Receiver it will be green. The color for the Streamer can change depending on the setup method and the brand of your streaming device. The One For All remote is pre-programmed for a Roku streaming box so the default color is purple, and if you follow the SimpleSet procedure to set up another brand (see simplest), it will change to a color associated with the brand you chose, for example, dark green for a Microsoft Xbox.
If you set up using a code (see Code Setup), the color for your streamer will be red. You can even choose a color yourself – see the section Choose Color.

CHOOSE COLOR

Once you have set up your devices, the color of the menu ring reflects the devices you are controlling. For TV functions, the ring is yellow, for Audio green, and for your streaming device it can be read, or a brand color if you used the SimpleSet method.
However if you’d prefer to choose your own color to represent streamer control, you can. There are dozens of shades to choose from, and the procedure is simple.
To perform this:

1. Hold down Channel Up and Channel Down until the ring blinks twice red
2. Press the Channel Up key. The ring will light up white and stay lit
3. Now each press of the Channel Up key will change the ring to a different color. Pressing Channel Down will take it back to the previous color. There are over 100 different shades to choose from.
4. Once you have found the color you like, press and hold down the OK key.
   The ring will blink twice in the current color. From now on, when you are controlling your Streaming box the ring will light up in the color you have chosen.

• If you reach the last color, the ring will blink red twice and the color will not be stored.
• If you do not press a key for 10 seconds, the light will go out and no color will be stored
• If you want to change the color at any point, just repeat the process.

APP SHORTCUT FEATURE

The Streaming Remote features 4 App Shortcut keys for viewing streamed content. If your original remote control already had a key for this – for example, many Roku streamers will have a Netflix and Amazon key – then this key will perform exactly the same as the key on your original remote.

If your streamer supports these keys, they will function as Netflix, Amazon Video,
Hulu, and YouTube.
However, if you did not have a key like this, you can use this key as a shortcut to a streaming app
by programming a macro on it. You can set a macro to any service supported by an app on your streaming device. So if you would prefer HBO Now or Plex, no problem.
To program the macro, you first need to know the sequence of keys you need to press to always bring up the service you prefer, For example on an Apple TV, the sequence for Netflix is Back (or Home), Menu Down, and OK.

APP SHORTCUT FEATURE

Once you have determined the sequence for your device, follow these steps:

1. Sit in front of your device with It switched on (not on standby)
2. Hold down the App Shortcut key (for example the “N” key) until the LED blinks twice
3. Now perform the sequence of keys exactly as you would normally. The remote will operate your device and the macro is recorded in real-time – so if it normally takes a few seconds for your device to react don’t worry.
4. Once you have finished the sequence – and the Streaming Service has started on your device
   – hold down the App Shortcut key until the LED blinks green twice and go out. The macro is now stored.

Tips

• Make sure the Streamer Is operating the device in question before programming
• If you find the Macro doesn’t work as expected, you can just repeat the same sequence to reprogram
• When programming, wait for your device to respond first, the remote will remember the timing

MORE FUNCTIONS ONLINE

Although all the major features of your One For All remote are covered in this guide, there is even more functionality available online. For example, you could set the remote into a “CEC Mode” that may control streamers that cannot be controlled by infrared, or potentially reprogram the input key to always select the same input on your TV. You can find tutorials, tips, and extra info for this remote and others at:

www.oneforall.com/universal-remotes/urc-7935-streamer-remote

http://www.oneforall.com/universal-remotes/urc-7935-streamer-remote
Customer Support:
855-716-2573 (toll-free)
03-09-2020 16:52
03-09-2020 16:52

URC7125 SIMPLE SET UP GUIDE

CAUTION: Risk of explosion if the battery is replaced by an incorrect type. Use quality Alkaline batteries.

KEY TABLE

HOW TO SET UP YOUR REMOTE

A – SIMPLE SET

simplest is a quick and easy way of setting up the remote to control the most popular brands of each device type with only a few key presses, typically in under a minute per device. The first step is to select which device you are going to set up. The following is a list of Device Modes on the remote control, and the Device types that can be set up on that mode:

For each Device type, there is a list of the top brands, each with a number assigned to it, for example, 6 for a Samsung TV. Locate your device and brand in the list that follows:

TV

STB: Sat, Cable, DVB-T

HOW TO SET UP YOUR REMOTE

A – SIMPLESET
To set up your device

1. Turn on your device (not on standby) and point the OFA remote towards it.
2. Hold down MAGIC until the LED under the device blinks twice. The LED under the current device will stay lit.
3. Press the MODE key repeatedly until the LED for the device you want to set up is lit.
4. Hold down the digit for your brand and device as listed above (e.g. 6 for Samsung TV).
5. The remote will send Power every 3 seconds until your device switches off.
6.  As soon as your device switches off, release the digit.
7. The LED will blink twice and go out. The remote should now operate your device.

• If you find one or more keys do not work as you expect, start again at step 1 – the remote will start with the next code in the memory.

HOW TO SET UP YOUR REMOTE

B – SET UP BY CODE
If your brand is not listed in section A, you can set up your device by trying codes individually.
To do this:

1. Turn your device on (not on standby).
2. Locate the brand of your device in the code list (pages 126-137). Codes are listed by Device Type and Brand.
3. Hold down MAGIC until the LED under the device blinks twice. The LED under the current device will stay lit.
4. Press the MODE key repeatedly until the LED for the device you want to set up is lit.
5. Enter the first 4 digit code listed for your brand (e.g. 4542 for an Aiwa TV).
6. The LED will blink twice and go out.
7. Now aim the remote towards your device and press the POWER key.
8. If the device turns off, your remote is ready to use. If not, repeat steps 3-7 with the next code in the list.

• Some codes are quite similar. If you find that one or more keys do not operate as you expect, try again from step 3 with the next code in the list.

LEARNING

Your One For All remote control can learn any function from any other working remote control.
This can be useful if you are missing one or more functions from your original remote control and would like to add them to the ONE FOR ALL. You can learn onto any key except MAGIC or MODE.
You can also learn a complete device if you can’t find a code.
To learn, firstly make sure you have all your original remote controls to hand, and that they have working batteries in. To learn functions, the original remote should be  approximately 3cm from the OFA remote, pointing towards it as shown below:

1. Hold down MAGIC until the LED under the device blinks twice.
   The LED under the current device will stay lit.
2. Press the MODE key repeatedly until the LED for the device you want to learn functions on is lit.
3. Press 975 – the LED will blink twice.
4. Press and release the key you want to learn a function onto (for example the HOME key) – The red LED will blink continuously.
5. Press and release the key on the original remote.
6. The LED will blink twice to indicate the key has been learned correctly.
7. Repeat steps 4 and 5 for each key you want to learn – remember you can learn from multiple remotes, but only one function per key.
8. When you learned all the functions you require, press and hold the MAGIC key until the LED blinks twice and turns off.

HINTS

• If the LEDs show one long blink at step 6, the function was not learned correctly, please try again from step 4.
• If you find one or more keys don’t work properly after set up, you can re-enter the learning mode at any time by repeating the procedure from step 1.

TO DELETE A LEARNED FUNCTION, THE PROCEDURE IS:

1. Hold down MAGIC until the LED under the device blinks twice.
   The LED under the current device will stay lit.
2. Using the MODE key, make sure the LED for the device you want to delete functions from is lit.
3. Press 976 – the LED will blink twice
4. Press the key to delete twice – the LED will blink twice.

Repeat the above procedure for each key you want to delete.

ACTIVITIES

The Watch TV feature combines TV and STB into a single-mode. In this mode, the Volume and AV keys will control the TV, and the rest of the keys will control the STB.
As the AV key is intended to select the input on your TV and most TVs use a menu to select from a list of inputs, when the AV key is pressed in Watch TV Mode, the Menu Up, Down, Left, Right and OK keys temporarily control the TV. If the OK key is pressed, or no key is pressed for ten seconds, these keys will revert to controlling the STB.
If you hold down the Power key for 2 seconds in Watch TV Mode, the remote will send the Power function for TV and STB.

THE NETTV FEATURE

The Evolve features a “NETTV” key for viewing digital TV, streamed over the internet. If your original remote control already had a key for this – for example, many newer TVs have a Netflix key – then this key will perform exactly the same as the key on your original remote. However, if you did not have a key like this, but still had the ability to watch a streaming service, you can use this key as a shortcut by programming a macro on it. Most AV devices that are connected to the internet, such as Smart TVs or streaming
Set-Top Boxes to have one or more applications they can run to access TV viewing via the internet. Examples of these would be Netflix, YouTube, Amazon Prime, BBC iPlayer, or similar.
To program the macro, you first need to know the device you use to access the service, and then the sequence of keys you need to press to always bring up the service you prefer, For example, some Panasonic TVs will start Netflix by pressing the Apps key, then Menu Down Twice, and finally the OK key. Or on an Apple TV, the sequence is Menu, Menu Down, and OK.
Once you have determined the sequence for your device, follow these steps:

1. Sit in front of your device with It switched on (not on standby)
2. Hold down the NETTV key until the LED blinks twice and stays lit
3. Use the MODE key to select the device you want to use for the NETTV macro (e.g. TV)
4. Now perform the sequence of keys exactly as would normally. The remote will operate your device and the macro is recorded in real-time – so if it normally takes a few seconds for your device to react don’t worry.
5. Once you have finished the sequence – and the Streaming Service has started on your device – hold down the NETTV key until the LED blinks twice and goes out. The macro is now stored.

Tips

• Make sure the Evolve Is operating the device in question before programming If you find the Macro doesn’t work as expected, you can just repeat the same sequence to reprogram
• When programming, wait for your device to respond first, the remote will remember the timing
• The NETTV macro is tied to one device, remember to make sure you are watching the correct device.

MACROS

PROGRAM A MACRO
You can program any key on your OFA remote (except MAGIC or MODE) to send multiple commands on a single press –a Macro. This can be useful for controlling multiple devices to put them in a certain state – for instance, you could put your TV on HDMI 1 and press Power on the Set-Top Box to start watching TV.
To program a macro, the procedure is as follows:

1. Hold down MAGIC until the LED under the device blinks twice.
   The LED under the current device will stay lit.
2. Press 995 – the LED will blink twice.
3. Next, select the key you want to program the Macro on.
4. Now use the MODE key to select the device you want the first function of the Macro to come from, for example, TV.
5. Next, press the key you want to include in the Macro, for example, the AV key.
6. Repeat steps 4 (if necessary) and 5 to add more keys to the Macro. You can include up to 15 key presses.
7. To store the Macro, hold down the MAGIC key until the LED blinks twice.

• If the LED shows a long blink when you press a key in steps 4 or 5, you have entered too many keys, please try again.

DELETING A MACRO

If you want to remove a macro from a key, please perform the following:

1. Hold down MAGIC until the LED under the device blinks twice. The LED under the current device will stay lit.
2. Press 995 – the LED will blink twice.
3. Press the key the macro is programmed on.
4. Now hold down the MAGIC key until the LED blinks twice – the Macro is deleted.

VOLUME LOCK

If you always use one device to control volume, for example, your TV, you can set up the One For All to always control that device, regardless of which device your remote is controlling. To do this:

1. Hold down MAGIC until the LED under the device blinks twice. The LED under the current device will stay lit.
2. Press 993 – the LED will blink twice.
3. Use the MODE key to select the Device you want to lock the Volume to.
4. Press MAGIC once – the LED will blink twice and the volume is now locked.

To unlock the volume and set every device back to controlling its own volume, the procedure is:

1. Hold down MAGIC until the LED under the TV key blinks twice. The LED under the current mode key will stay lit.
2. Press 993 – the LED will blink twice.
3. Press VOLUME UP – the LED will blink twice and Volume is now unlocked.

PRODUCT DISPOSAL (EUROPEAN DIRECTIVE 2012/19/EU)

The crossed-out wheeled bin symbol on this product ensures that this product is manufactured using high-quality components that can be recycled and reused according to European Directive 2012/19/EU. Please do not dispose of this product with your normal household waste, refer to local regulations for the proper collection or disposal of electrical and electronic products. This will help in preventing negative effects on the environment and/or human health.
BATTERY DISPOSAL (EUROPEAN DIRECTIVE 2006/66/EC)Please do not dispose of your batteries with your normal household waste, refer to local regulations for the proper collection or disposal. This will help to prevent potential negative effects on the environment and/or human health.
GUARANTEE TERMS AND CONDITIONS UNIVERSAL ELECTRONICS warrants to the original purchaser that this product will be free from defects in materials and workmanship under normal and correct use for a period of two (2) years from the date of original purchase. This product will be repaired or if necessary, replaced free of
charge if it has been proven to be defective within the two(2) year warranty period. The forwarding costs are on the account of the owner; the costs of returning the product are on the account of UNIVERSAL ELECTRONICS.
This warranty does not cover damage or failures caused by products or services not supplied by UNIVERSAL ELECTRONICS, or which result from not mounting the product according to manual instructions. This also applies when the product has been modified/repaired by others than UNIVERSAL ELECTRONICS or if a fault is the result of an accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, improper maintenance, alteration, modifications, fire, water, lightning, natural disasters, wrong use or carelessness.
To obtain warranty service during the warranty period contact […], and please note that we need your original purchase receipt so that we may establish your eligibility for service. If you have bought this product for purposes that are not related to your trade, business, or profession, you may have legal rights under your national legislation governing the sale of consumer goods. This guarantee does not affect those rights.
www.oneforall.com

Connect with us

facebook.com/oneforallworldwide
@oneforall.worldwide
linkedin.com/company/one-for-all-worldwide/
youtube.com/user/oneforallproducts

Universal Electronics BV
Europe & International
Colosseum 2, 7521 PT Enschede
The Netherlands

URC7125
711733
RDN-1201120

ONE FOR ALL URC1240 Universal Remote Control

Universal Remote Control

Television / HDTV / LCD / LED / Plasma / Projector

DVD Player / DVD-R / Blu-ray / DVD Home Cinema / DVD/VCR Combi / DVD/HDD

VCR / Video Recorder / VCR/DVD Combi

Digital TV Receiver / Satellite Receiver / Set-Top-Box / IPTV / DVB-S / DVB-T / Freeview (UK) / SAT/HDD / Cable Converter / Set-Top-Box / IPTV / DVB-C / Video Accessory like Media Centres / AV Accessories / AV Selectors / Game Console

Audio / Audio Receiver/Tuner/Amplifier / (DVD) Home Cinema

MP3 / MP3 Dock

Requires 2 new AAA Batteries

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Use quality Alkaline batteries.

Code Set up

(Example: To set up the ONE FOR ALL REMOTE for your television)

1. Find the four-digit device code for your device (e.g. Aiwa television) in the Code list. Codes are listed by device type and brand name. The most popular code is listed first. If your brand is not listed at all please try the Code Search. Make sure your equipment is switched on. If not switch it on manually.
   
2. Select the device key (e.g. TV key) corresponding to the device you wish to control (e.g. television).
   
3. Press and hold down the SETUP key until the red LED underneath the POWER key blinks twice (the red LED will blink once then twice).
   
4. Enter your four-digit device code using the number keys (e.g. TV – Aiwa code 4542). The red LED lights up twice.
   
5. Now, aim the ONE FOR ALL at your device and press POWER. If your device switches off, the ONE FOR ALL REMOTE is ready to operate your device. If it does not switch off your device simply try the next code listed for your brand.
   

If none of the codes listed for your brand work please try the Code Search. The Code Search may also work if your brand is not listed at all.
To set up the code for another device follow the instructions above only press the appropriate device key instead of TV during step 2.

Code Search

The Search Method allows you to find the code for your device by scanning through all the codes contained in the memory of the ONE FOR ALL. The Search Method may also work if your brand is not listed at all.

1. Switch on your television (not on standby).
2. Select the device key (e.g. TV key) corresponding to the device you wish to control (e.g. television).
3. Press and hold down the SETUP key until the red LED underneath the POWER key blinks twice (the red LED will blink once then twice).
4. Press 9 9 1. The red LED will blink twice.
5. Next, press POWER.
6. Aim the ONE FOR ALL at your Television. Now press CH+ over and over, until your Television turns off (everytime you press the CH+ key the ONE FOR ALL will send out a POWER signal from the next code contained in the memory). You may have to press this key many times (up to 150 times) so please be patient.
7. As soon as your television turns off, press the SETUP key to store the code.

Learning (copy)

Your One For All remote control can learn any function from any other working remote control. To do this, firstly make sure you have all your original remote controls to hand, and that they have working batteries in. To learn functions, the original remote should be approximately 3cm from the OFA remote, pointing towards it as shown below:

1. Select the corresponding device e.g. TV
2. Press and hold down the SETUP key until the red LED underneath the POWER key blinks twice (the red LED will blink once then twice).
3. Press 9 7 5
4. Press and release the key you want to learn a function onto (for example the TV Power key) ­ The red LED will blink continuously.
5. Press and release the corresponding key on the original remote, for example Power.
6. The red LED will blink twice to indicate the key has been learned correctly.
7. Repeat steps 4 and 5 for each key you want to learn ­ remember you can learn from multiple remotes, but only one function per key.
8. When you learned all the functions you require, press and hold the SETUP key until the red LED blinks twice.

• If the red LED shows one long blink at step 6, the function was not learned correctly, please try again from step 4.
• If you find one or more keys don’t work properly after set up, you can re-enter the learning mode at any time by repeating the procedure from step 1.

How to delete a learned function to obtain the original function?

1. Select the corresponding device mode (e.g. TV).
2. Press and hold down the SETUP key until the red LED underneath the POWER key blinks twice (the red LED will blink once then twice).
3. Press 9 7 6.
4. Press the key to be deleted (e.g. red key) twice.

Volume Lock

This feature gives you the possibility to set the Volume (VOL+, VOL- and Mute) to always control a certain device (e.g. tv) independent of which device mode key (TV, SAT, DVD or AMP) is selected.

In this example we will set Volume Control (VOL+, VOL- and Mute) to “tv volume”:

1. Press and hold down the SETUP key until the red LED underneath the POWER key blinks twice (the red LED will blink once then twice).
2. Press 9 9 3.
3. Then press the TV key and the red light will blink twice.

Now you have set the Volume Control to “tv volume”. The VOL+, VOL- and Mute keys will always control “tv volume” independent which device mode key (TV, SAT, DVD or AMP) is selected.

How to deactivate Volume Control

1. Select the device key you wish to deactivate from Volume Control (e.g. AMP).
2. Press and hold down the SETUP key until the red LED underneath the POWER key blinks twice (the red LED will blink once then twice).
3. Press 9 9 3.
4. Press the VOL(+) key and the red LED will blink four times.

Connect with us

facebook.com/oneforallworldwide
@oneforall.worldwide
linkedin.com/company/one-for-all-worldwide/
youtube.com/user/oneforallproducts

Universal Electronics BV
Europe & International
Colosseum 2, 7521 PT Enschede
The Netherlands

FOR ALL
URC7115
SIMPLE SET UP GUIDE

KEY TABLE

HOW TO SET UP YOUR REMOTE

A – SIMPLE SET

simplest is a quick and easy way of setting up the remote to control the most popular brands of each device type with only a few key presses, typically in under a minute per device.
For each Device type, there is a list of the top brands, each with a number assigned to it, for example, 6 for a Samsung TV. Locate your device and brand in the list that follows:

TV

To set up your device

1. Turn on your device (not on standby) and point the OFA remote towards it.
2. Hold down MAGIC until the LED blinks twice.
3. Hold down the digit for your brand and device as listed above (e.g. 6 for Samsung TV).
4. The remote will send Power every 3 seconds until your device switches off.
5. As soon as your device switches off, release the digit.
6. The LED will blink twice and go out. The remote should now operate your device.

• If you find one or more keys do not work as you expect, start again at step 1 – the remote will start with the next code in the memory.

HOW TO SET UP YOUR REMOTE

B – SET UP BY CODE
If your brand is not listed in section A, you can set up your device by trying codes individually.
To do this:

1. Turn your device on (not on standby).
2. Locate the brand of your device in the code list (pages 74-77). Codes are listed by Device Type.
3. Hold down MAGIC until the LED blinks twice.
4. Enter the first 4 digit code listed for your brand (e.g. 4542 for an Aiwa TV).
5. The LED will blink twice and go out.
6. Now aim the remote towards your device and press the POWER key.
7. If the device turns off, your remote is ready to use. If not, repeat steps 3-6 with the next code in the list.

• Some codes are quite similar. If you find that one or more keys do not operate as you expect, try again from step 3 with the next code in the list.

LEARNING

Your One For All remote control can learn any function from any other working remote control.
This can be useful if you are missing one or more functions from your original remote control and would like to add them to the ONE FOR ALL.
You can also learn a complete device if you can’t find a code.
To learn, firstly make sure you have all your original remote controls to hand, and that they have working batteries in. To learn functions, the original remote should be approximately 3cm from the OFA remote, pointing towards it as shown below:

1. Hold down MAGIC until the LED blinks twice.
2. Press 975 – the LED will blink twice.
3. Press and release the key you want to learn a function onto (for example the HOME key) – The red LED will blink continuously.
4. Press and release the key on the original remote.
5. The LED will blink twice to indicate the key has been learned correctly.
6. Repeat steps 3 and 4 for each key you want to learn – remember you can learn from multiple remotes, but only one function per key.
7. When you learned all the functions you require, press and hold the MAGIC key until the LED blinks twice and turns off.

HINTS

• If the LED shows one long blink at step 5, the function was not learned correctly, please try again from step 3.
• If you find one or more keys don’t work properly after set up, you can re-enter the learning mode at any time by repeating the procedure from step 1.

TO DELETE A LEARNED FUNCTION, THE PROCEDURE IS:

1. Hold down MAGIC until the LED blinks twice.
2. Press 976 – the LED will blink twice
3. Press the key to delete twice – the LED will blink twice.

Repeat the above procedure for each key you want to delete.

THE NETTV FEATURE

The Evolve features a “NETTV” key for viewing digital TV, streamed over the internet. If your original remote control already had a key for this – for example, many newer TVs have a Netflix key – then this key will perform exactly the same as the key on your original
remote. However, if you did not have a key like this, but still had the ability to watch a streaming service, you can use this key as a  shortcut by programming a macro on it. Most AV devices that are connected to the internet, such as Smart TVs or streaming  Set-Top Boxes have one or more applications they can run to access TV viewing via the internet.

THE NETTV FEATURE

Examples of these would be Netflix, YouTube, Amazon Prime, BBC iPlayer, or similar.
To program the macro, you first need to know the device you use to access the service, and then the sequence of keys you need to press to always bring up the service you prefer, For example, some Panasonic TVs will start Netflix by pressing the Apps key, then  Menu Down Twice, and finally the OK key.

Once you have determined the sequence for your device, follow these steps:

1. Sit in front of your device with It switched on (not on standby)
2. Hold down the NETTV key until the LED blinks twice and stays lit
3. Now perform the sequence of keys exactly as would normally. The remote will operate your device and the macro is recorded in real-time – so if it normally takes a few seconds for your device to react don’t worry.
4. Once you have finished the sequence – and the Streaming Service has started on your device -hold down the NETTV key until the LED blinks twice and goes out. The macro is now stored.

Tips

• Make sure the Evolve Is operating the device in question before programming
• f you find the Macro doesn’t work as expected, you can just repeat the same sequence to reprogram
• When programming, wait for your device to respond first, the remote will remember the timing

English – PRODUCT DISPOSAL (EUROPEAN DIRECTIVE 2012/19/EU)
The crossed-out wheeled bin symbol on this product ensures that this product is manufactured using high-quality components that can be recycled and reused according to European Directive 2012/19/EU. Please do not dispose of this product with your normal household waste, refer to local regulations for the proper collection or disposal of electrical and electronic products. This will help this will help in preventing negative effects on the environment and/or human health.
BATTERY DISPOSAL (EUROPEAN DIRECTIVE 2006/66/EC)Please do not dispose of your batteries with your normal household waste, refer to local regulations for the proper collection or disposal. This will help to prevent potential negative effects on the environment and/or human health.

GUARANTEE TERMS AND CONDITIONS UNIVERSAL ELECTRONICS warrants to the original purchaser that this
product will be free from defects in materials and workmanship under normal and correct use for a period of two (2) years from the date of original purchase. This product will be repaired or if necessary, replaced free of charge if it has been proven to be defective within the two(2) year warranty period. The forwarding costs are on the account of the owner; the costs of returning the product are on the account of UNIVERSAL ELECTRONICS.
This warranty does not cover damage or failures caused by products or services not supplied by UNIVERSAL ELECTRONICS, or which result from not mounting the product according to manual instructions. This also applies when the product has been modified/repaired by others than UNIVERSAL ELECTRONICS or if a fault is the result of an accident, misuse, abuse, neglect, mishandling, misapplication, faulty installation, improper maintenance, alteration, modifications, fire, water, lightning, natural disasters, wrong use or carelessness.

To obtain warranty service during the warranty period contact […], and please note that we need your original purchase receipt so that we may establish your eligibility for service. If you have bought this product for purposes that are not related to your trade, business, or profession, you may have legal rights under your national legislation governing the sale of consumer goods. This guarantee does not affect those rights.www.oneforall.com

Connect with us

facebook.com/oneforallworldwide

@oneforall.worldwide

linkedin.com/company/one-for-all-worldwide/

youtube.com/company/one-for-allworldwide/user/oneforallproducts

Universal Electronics BV
Europe & International
Colosseum 2, 7521 PT Enschede
The Netherlands

URC7115
711727
RDN-1201120

Before returning this product please call us for support

Customer Support:

Imported into the US by:
Universal Electronics Inc.
UEI Technical Support Services,
Suite 301
26250 Euclid Ave.
Euclid, OH 44132

One For All is a registered trademark of UEI
Made in Taiwan

www.oneforall.com/assistantapp

– Avoid metal surfaces (like a metal stand)
– Move the antenna close to or in a window
– Position the antenna as high as possible

WARRANTY / GUARANTEE INFORMATION
1 Year Limited Warranty against defects in material and workmanship can be found at www.oneforall.com/warranty, or you may request a hard copy by calling 855-569-6595, or via mail to UEI Technical Support Service, Suite 301, 26250 Euclid Ave., Euclid, OH 44132.
Please include your full name, product information, and contact information in your request communication.

LIMITED WARRANTY

Warranty: Universal Electronics Inc. warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase. This warranty does not apply to damage caused by shipping or handling, or damage caused by accident, abuse, misuse, misapplication, ordinary wear, improper maintenance, failure to follow instructions or as a result of any unauthorized modifications. The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Universal Electronics Inc. neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. The maximum liability for Universal Electronics Inc. under all circumstances for any warranty issue shall be limited to a replacement of the defective product. It is recommended that the customer check their equipment on a regular basis for proper operation.

Remedies: Your exclusive remedy under this Limited Warranty is that Universal Electronics Inc., at its option, will repair or replace, without charge for parts and/or labor, the product found to be defective.

Service Procedure: To obtain warranty service, visit www.oneforall.com/warranty and complete the form with your full name, contact information, product serial number, and description of the issue along with a legible copy/ image of your sales receipt showing date of purchase.

Disclaimer: THE FOREGOING LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY BY UNIVERSAL ELECTRONICS INC. WITH RESPECT TO THE PRODUCTS. THERE ARE NO OTHER REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, EXCEPT AS REQUIRED BY APPLICABLE LAW. ANY IMPLIED WARRANTIES REQUIRED BY LAW ARE LIMITED IN DURATION TO WARRANTY PERIOD PROVIDED HEREIN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

IN NO EVENT SHALL UNIVERSAL ELECTRONICS INC. OR ANY OF ITS AFFILIATES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, CONSEQUENTIAL, OR MULTIPLE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOST PROFITS, LOST OR DAMAGE TO SOFTWARE OR DATA, OR DAMAGE TO EQUIPMENT ARISING OUT OF THE USE OF ANY PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS STANDARD WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

Reception quality and the numbers of channels received are dependent on multiple factors like distance from TV broadcast tower, broadcast power, line of sight, terrain, metal construction materials and other environmental factors.

LEGAL NOTICES

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

(x2) (x2)

1
FIRST connect the USB cable to the power adapter. Alternatively you can plug the USB cable in one of your USB ports on the side or back of your TV (if available).
OR

2
Then connect the coaxial cable attached to the ANTENNA IN connector at the back w the TV or set-top box.

3 Decide how you would like to position the antenna:
WALL MOUNTED or FLAT.
Decide how you would like to position the antenna: FLAT or WALL MOUNTED. When mounting to a wall, you will have to drill 2 holes in your wall whereas the distance between the center of the holes should be 140 mm. Put the plugs in the holes and put the screws in the plugs.

We do suggest you to FIRST finalize this set up before drilling holes, since you might need to re-position the antenna for best reception.

Position the antenna as high as possible and move close to or in a window and facing the directions of the TV towers for best reception. A / B or C. If you are not sure in which direction your TV towers are, please check www.channelchecker.com and it will tell you in 3 simple steps.

IMPORTANT!

For detailed instructions on how to perform a channel scan, please see the manual provided with your TV.

In order to improve the reception performance you might look for a different position of the antenna by moving closer to or in a window and facing the direction of the TV towers.

You can also rotate the antenna while lying flat or standing for finetuning in order to improve reception even more.

IMPORTANT!

ONE FOR ALL URC-7140 Essence 4 Universal Remote Control

Instruction

Direct Code Set Up

1. Find the code for your device in the Code list (page 92 – 103). Codes are listed by device type and brand name. The most popular code is listed first. Make sure your device is switched on (not on standby)
2. Press and hold magic for 3 seconds until the blue LED (any LED) stays on.
3. Select the corresponding device e.g. TV
4. Enter the 1st code listed for your device type & brand (e.g. TV Hitachi = 1576)
   1. > The blue LED will blink twice and then Switch off.
5. If your device does NOT switch off?> Please repeat steps 1 – 5 trying the next code listed for your brand.
   1. If NOT successful? > Try the Search Method.

Search Method

The Search Method allows you to find the code for your device by scanning through all the codes contained in the memory of the ONE FOR ALL. The Search Method may also work if your brand is not listed at all.Example: To search for your TV code: Switch on television (not on standby) and aim your ONE FOR ALL at your TV.

1. Press and hold MAGIC for 3 seconds until the blue LED (any LED)  stays on.
2. Select the corresponding device e.g. TV
3. Press 9 9 1. The blue LED will blink twice (showed by going out twice).
4. Next, press POWER.
5. Press CH+ (over and over) again until your device switches OFF.
   You may have to press these keys many times (up to 150 times) so please be patient.
6. As soon as your television turns off, press the magic key to store the code.

Volume Control

In this example we will set Volume Control (VOL+, VOL- and Mute) to “TV volume”:

1. Press and hold MAGIC for 3 seconds until the blue LED (any LED) stays on.
2. Press 9 9 3. The blue LED will blink twice.
3. Select the corresponding device e.g. TV.
4. Press and hold the magic key for 3 sec. The blue LED will blink twice and then Switch off.

Now you have set the Volume Control to “TV volume”. The VOL+, VOL- and
Mute keys will always control “TV volume” independent which device mode key (TV, SAT, DVD or AMP) is selected.

How to deactivate Volume Control

1. Press and hold MAGIC for 3 seconds until the blue LED stays on.
2. Press 9 9 3.
3. Press Vol +. The blue LED will blink 4 times.

All devices will send out their own VOL+, VOL- and MUTE.

How to remove a device from Volume Control

1. Press and hold MAGIC for 3 seconds until the blue LED stays on.
2. Press 9 9 3.
3. Select the device mode you wish to deactivate from Volume Control.
4. Press Vol -. The blue LED will blink 4 times.

The removed device will send out its own VOL+, VOL- and MUTE.

The Learning Feature

(How to copy functions from your original working remote onto the ONE FOR ALL 4)

Example: How to learn (copy) the “I/II (mono/stereo)“ function from your original remote onto the “red key” on your ONE FOR ALL remote control.

1. Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit.
2. Select the corresponding device e.g. TV
3. Press 9 7 5
   1. The blue LED will blink twice.
4. ATTENTION: Place both remote controls on a flat surface. Make sure that the ends you normally point at your device are facing each other. Align both remotes also in height
   1. First; Press the ”red” key. The TV LED will flash rapidly.then; Press the “I/II (mono/streo)” key. The blue LED will blink twice to
      confirm successful learning.
5. Press and hold the magic key for 3 sec.
   1. > The blue LED will blink twice and switch off.

Congratulations! You successfully learned (copied) the “I/II (mono/stereo)” function from your original remote control onto your ONE FOR ALL remote control. NOW whenever you press the “red key” (in TV mode) you will obtain the “I/II (mono/streo)” function.

How to delete a learned function to obtain the original function?

1. Press and hold MAGIC for 3 seconds until a mode indicator (Blue LED) stays lit.
2. Press 9 7 6.
3. Select the corresponding device mode (e.g. TV).
4. Press the key to be deleted (e.g. red key) twice.

ONE FOR ALL Combi Control

By now you probably have set up the ONE FOR ALL remote to control all (or most of) your devices. Wouldn’t it be convenient if you wouldn’t have to select a device type all the time. You can make this possible with ONE FOR ALL Combi Control. Combi Control enables you to control up to 3 devices simultaneously (e.g control TV + SAT simultaneously).

Example: How to activate “Combination 2” (See the key pad configuration on page 111).

1. Press and hold magic for 3 seconds until a mode indicator (Blue LED) stays lit.
   
2. Press Combi Control.
3. Press 2 (to select combination 2).

Master Power (in Combi Control)

In Combi Control the POWER key will switch ON/OFF all devices within the activated Combi Control Setting – simply by pressing it for 3 seconds. E.g. within Combi Control combination 2 you can switch OFF your TV, SAT and AMP by by pointing towards these devices and simply press and hold the POWER key for 3 seconds.

Start by checking if the brand of your particular device is listed in the “SimpleSet” brand list and check which “number key” is assigned to your brand (e.g. Bush tv = 1).

1. Press and hold MAGIC for 3 seconds until a mode indicator (Blue LED) stays lit.
2. Select the device you wish to set up (e.g. tv).
3. Press and hold the “number key” according to your brand (e.g. for Bush tv = press 1) until your device switches off. The blue LED will switch off every 3 seconds as a ‘power

signal’ is being sent. Make sure to release this “number key” as soon as your device switches OFF to complete the set up.

• If your brand is not listed in the “SimpleSet – brand list”? –> Go to the Direct Code Set up (page 8).
• The ONE FOR ALL is not performing commands properly? –> Simply repeat SimpleSet
• If SimpleSet is unsuccessful? –> Go to the Direct Code Set Up or try the Search Method.

QUICK INSTALLATION GUIDE
14450 / 14451
SMART ANTENNA

Before returning this product please call us for support

Customer Support:
855-823-3422
(toll-free)

OFA warranty/terms & conditions: 855-569-6595 (toll free)
www.oneforall.com
Imported into the US by:
Universal Electronics Inc.
UEI Technical Support Services,
Suite 301
26250 Euclid Ave.
Euclid, OH 44132
One For All is a registered trademark of UEI
Made in Taiwan, Hecho en Taiwán

Download the FREE

www.oneforall.com/assistantapp

PLACEMENT TIPS FOR ANTENNAS:

– Avoid metal surfaces (like a metal stand)
– Move the antenna close to or in a window
– Position the antenna as high as possible

WARRANTY / GUARANTEE INFORMATION

1 Year Limited Warranty against defects in material and workmanship can be found at www.oneforall.com/ warranty, or you may request a hard copy by calling 855-569-6595, or via mail to UEI Technical Support Service, Suite 301, 26250 Euclid Ave., Euclid, OH 44132.
Please include your full name, product information, and contact information in your request communication.
LIMITED WARRANTY
Warranty: Universal Electronics Inc. warrants this product to be free from defects in material and workmanship for a period of one year from the date of purchase. This warranty does not apply to damage caused by shipping or handling or damage caused by accident, abuse, misuse, misapplication, ordinary wear, improper maintenance, failure to follow instructions, or as a result of any unauthorized modifications. The foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties, whether expressed or implied, and of all other obligations or liabilities on the part of Universal Electronics Inc. neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. The maximum liability for Universal Electronics Inc. under all circumstances for any warranty issue shall be limited to a replacement of the defective product. It is recommended that the customer check their equipment on a regular basis for proper operation.

Remedies: Your exclusive remedy under this Limited Warranty is that Universal Electronics Inc., at its option, will repair or replace, without charge for parts and/or labor, the product found to be defective.

Service Procedure: To obtain warranty service, visit www.oneforall.com/warranty and complete the form with your full name, contact information, product serial number, and description of the issue along with a legible copy/ image of your sales receipt showing date of purchase.

Disclaimer: THE FOREGOING LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY BY UNIVERSAL
ELECTRONICS INC. WITH RESPECT TO THE PRODUCTS. THERE ARE NO OTHER REPRESENTATIONS OR WARRANTIES,
EXPRESS OR IMPLIED, EXCEPT AS REQUIRED BY APPLICABLE LAW. ANY IMPLIED WARRANTIES REQUIRED BY LAW
ARE LIMITED IN DURATION TO THE WARRANTY PERIOD PROVIDED HEREIN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

IN NO EVENT SHALL UNIVERSAL ELECTRONICS INC. OR ANY OF ITS AFFILIATES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, CONSEQUENTIAL, OR MULTIPLE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOST PROFITS, LOST OR DAMAGE TO SOFTWARE OR DATA, OR DAMAGE TO EQUIPMENT ARISING OUT OF THE USE OF ANY PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS STANDARD WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.

Reception quality and the numbers of channels received are dependent on multiple factors like distance from TV broadcast tower, broadcast power, line of sight, terrain, metal construction materials and other environmental factors.

LEGAL NOTICES

FCC STATEMENT:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FIRST, connect the micro USB connector to the Power Inserter. THEN connect the included power adapter into any standard 120V wall outlet.

Then connect the coaxial cable attached to the ANTENNA IN connector at the back of the TV or set-top box.

This antenna has a unique Signal Level Indicator, which clearly shows the current strength of incoming TV signals. The more LEDs lighting up, the stronger the signal. PLEASE NOTE: You may live in a weak signal area where the incoming signals are not at full strength so not every LED will light up, however it may still be suff client to receive channels in good quality.

Decide how you would like to position the antenna:

STANDING UPRIGHT, WALL MOUNTED, or FLAT.

When you choose for STANDING UP, please use the included 2 stands and insert them into the 2 slots on the bottom of the rear of the antenna. When mounting to an interior wall, you have to drill 2 holes in your wall whereas the distance between the center of the holes should be 178 mm (7 inches). Put the plugs in the holes and put the screws in the plugs. We do suggest you FIRST finalize this setup before drilling holes since you might need to re-position the antenna for the best reception.
Position the antenna as high as possible and move close to or in a window and facing the direction of the TV towers for best reception.

If you are not sure in which direction your TV towers are, please check www.channelchecker.com and it will tell you in 3 simple steps.
In order to improve the reception performance, look for a different position of the antenna by moving closer to or in a window and facing the direction of the TV towers. A / B or C.
You can also rotate the antenna while lying at or standing for fine-tuning in order to improve reception even more.

TURN THE ANTENNA SLIGHTLY FOR BETTER SIGNAL STRENGTH OR RECEPTION QUALITY – www.oneforall.com/support/antennas

IMPORTANT! -FINAL STEP

Now you can perform a channel scan on your TV. Set the tuner mode of the TV to ANTENNA first, then choose CHANNEL SCAN (may be called AUTO PROGRAM, AUTO TUNING, AUTO SCAN, or CHANNEL SEARCH in the setup menu of your TV).
If the number of channels or the quality is poor, please change the antenna’s position and repeat step + + and RE-SCAN on your TV.

For detailed instructions on how to perform a channel scan, please see the manual provided with your TV.

FINISH
WWW.ONEFORALL.COM/TIPS-AND-TRICKS
Before returning this product
please call us for support
Customer Support: 855-823-3422 (toll free)
www.oneforall.com