ADVANTECH AIMB-706 LGA1151 Intel ATX with Dual Display, SAT 3.0, USB 3.1, DDR4 Manual

AIMB-706 LGA1151 Intel® Core™ i7/i5/i3 ATX with
Dual Display, SATA 3.0, USB 3.1, DDR4
Startup Manual

Packing List

Before you begin installing your card, please make sure that
the following items have been shipped:
• 1 x AIMB-706 Startup Manual
• 2 x Serial ATA HDD data cables
• 1 x Serial ATA HDD power cables
• 1 x I/O port bracket
If any of these items are missing or damaged, please contact your distributor or sales representative immediately.

Note: Acrobat Reader is required to view any PDF file. Acrobat Reader can be downloaded at: www.adobe.com/Products/acrobat/readstep2.html (Acrobat is a trademark of Adobe)

Specifications

Standard Functions
• CPU: LGA1151 socket supporting 8th/9th generation Intel® Core™ i7/i5/i3/Pentium/Celeron processor.
Note:

Intel 8th/9th generation processors only support Windows 10 (64-bit).
BIOS version V2.XX can support both 8th and 9th generation processors while BIOS version V1.XX can only support 8th generation processors.

BIOS: AMI 128 Mbit SPI BIOS.
Chipset: Intel® H310 PCH.
System Memory: Up to 32 GB in two 288-pin DIMM sockets supporting dual-channel DDR4 2400/2666 SDRAM. AIMB-706 supports non-ECC unbuffered DIMMs and does not support any memory configuration that mixes non-ECC with ECC unbuffered DIMMs.
Note: Due to the inherent limitations of the PC architecture, the system may not fully detect 32 GB RAM when 32 GB RAM is installed.
SATA Interface: Four onboard Serial ATA 3.0 connectors support data transmission rates up to 600 MB/s. All four SATA 3.0 ports support Advanced Host Controller

Interface (AHCI) technology.

PCIe and PCI Slot: 1 PCIe x16 expansion slot, 1 PCIe x4 expansion slot, 5 PCI slots 32-bit/33 MHz PCI 2.2 compliant.
LPC Interface: Advantech-designed LPC connector supports TPM module and COM port extension module.
Serial Port: Up to six serial ports: COMD1, COMD2 and COM4 ~ 6 are RS-232; COM3 is RS-232/422/485 with jumper and BIOS menu options.
Parallel Port: One parallel port, which supports SPP/ EPP/ECP mode.
Keyboard/Mouse Connector: Supports standard PS/2 keyboard and mouse.
Watchdog Timer: 255-sec timer level intervals.
USB 3.1/2.0: 4 USB 3.1 Gen 1 ports (2 rear, 2 via header), 5 USB 2.0 ports (2 rear, 2 via header, 1 internal Type-A).

Graphic Interface

Chipset: CPU integrated graphics controller.
Display Memory: 1 GB maximum shared memory with 2 GB and above system memory installed.
DVI-D: Resolution up to 1920 x 1200 @ 60 Hz refresh rate.
VGA: Resolution up to 1920 x 1200 @ 60 Hz refresh rate.

Ethernet Interface

Interface: 10/100/1000 Mbps.
Controller: LAN1: Intel ® I219-V; LAN2 (G2 sku only): Intel ® I211-AT.
Mechanical and Environmental
Dimensions (L x W): 304.8 x 244 mm (12” x 9.6”)
Power Supply Voltage: +3.3 V, ±5 V, ±12 V, +5 Vsb
Power Consumption: Intel Core i7-8700 3.2 GHz; DDR4 16GB x 2 Maximum: +3.3 V at 2.74 A, +5 V at 3.5 A, +12 V at 5.92 A, +5 Vsb at 0.05 A, -5 V at 0.01 A, -12 V at 0.08 A
Operating Temperature: 0 ~ 60° C (depending on CPU)
Weight of Board: 0.7 kg (1.54 lb)

Jumpers and Connectors

The board has a number of jumpers that allow you to configure your system to suit your application.
The table below lists the function of each jumper and connector.

Connector I -Wove	List
Label	Function
LPTI	Parallel port. supporting SPP/EPP/ ECP mode
LAN1	LAN1
LAN2	LAN2 (G2 sku only)
USB3CI	USB 3.1 Gen 1 port 1. 2
USB3H1	USB 3.1 Gen 1 port 1. 2 (20-pin header)
USB2C1	USB 2.0 port 1. 2
USB2A1	USB 2.0 port (internal Type-A)
USB2H1	USB 2.0 port 1. 2 (10-pin header)
VGAltDVII	VGA connector / DVI-D connector (DVII for G2 sku only)
COMD1+COMD2	Serial port: RS-232 (DB-9 connector)
COM4 – COMB	Serial port: RS-232 (9-pin header. G2 sku only)
COM3	Serial port: RS-232/4221485 (9-pin header. G2 sku only)
KBMS1	PS/2 keyboard and mouse connector
KBMS2	External keyboard and mouse connector (6-pin header)
CPUFAN1	CPU fan connector (4-pin)
SVSFAN1 – SVSFAN3	System fan connector (4-pin)
JFP3	Keyboard lock and power LED Suspend: fast flash (ATX/AT) System on: on (ATXJAT) System off: off (AT/ATX)
JFP2	External speaker / HDD LED connector / SMBus connector
JFPI	Power switch/reset connector
AUD101.AUD102	Audio connector (Line Out. Mic In)
VOLT’	Alarm board power connector
JCASEI	Case open connector
LANLEDI	Front panel LAN indicator connector
SATAO – SATA3	Serial ATA 3.0 port
PC11	PCI slot
PCl2	PCI slot
PCI3	PCI slot
PCI4	PCI slot

Connector I -Wove	List
Label	Function
LPTI	Parallel port. supporting SPP/EPP/ ECP mode
LAN1	LAN1
LAN2	LAN2 (G2 sku only)
USB3CI	USB 3.1 Gen 1 port 1. 2
USB3H1	USB 3.1 Gen 1 port 1. 2 (20-pin header)
USB2C1	USB 2.0 port 1. 2
USB2A1	USB 2.0 port (internal Type-A)
USB2H1	USB 2.0 port 1. 2 (10-pin header)
VGAltDVII	VGA connector / DVI-D connector (DVII for G2 sku only)
COMD1+COMD2	Serial port: RS-232 (DB-9 connector)
COM4 – COMB	Serial port: RS-232 (9-pin header. G2 sku only)
COM3	Serial port: RS-232/4221485 (9-pin header. G2 sku only)
KBMS1	PS/2 keyboard and mouse connector
KBMS2	External keyboard and mouse connector (6-pin header)
CPUFAN1	CPU fan connector (4-pin)
SVSFAN1 – SVSFAN3	System fan connector (4-pin)
JFP3	Keyboard lock and power LED Suspend: fast flash (ATX/AT) System on: on (ATXJAT) System off: off (AT/ATX)
JFP2	External speaker / HDD LED connector / SMBus connector
JFPI	Power switch/reset connector
AUD101.AUD102	Audio connector (Line Out. Mic In)
VOLT’	Alarm board power connector
JCASEI	Case open connector
LANLEDI	Front panel LAN indicator connector
SATAO – SATA3	Serial ATA 3.0 port
PC11	PCI slot
PCl2	PCI slot
PCI3	PCI slot
PCI4	PCI slot

JCMOS1: CMOS clear JME1: Intel ME update
Closed Pins	Result
2-Jan	Keep CMOS data Enable ME to update
3-Feb	Clear CMOS data Disable ME update
* Default

JWDT1+JOBS1: Watchdog timer output and OBS alarm
Closed Pins	Result
2-4, 8-10	Watchdog timer disable (2-4) OBS beep (8-10)
4-6, 8-10	*Watchdog timer reset (4-6) OBS beep (8-10)
* Default

PSON1: ATX/AT mode selection
Closed Pins	Result
1-2	AT mode
2-3	*ATX mode
* Default

JUSB_1 (rear USB), JUSB_2 (onboard USB): USB power source switch between +5V and +5V_DUAL
Closed Pins	Result
1-2	*USB +5V_DUAL power
2-3	USB +5V power
* Default

JSETCOM3: COM3 RS-232/422/485 jumper setting
Closed Pins	Result
5-6, 7-9, 8-10, 13-15, 14-16	*RS-232
3-4, 9-11, 10-12, 15-17, 16-18	RS-422
1-2, 9-11, 10-12, 15-17, 16-18	RS-485
* Default

Note: While RS-485 is selected, it is necessary to change device mode to RS-485 for further choice of auto flow control under the BIOS menu. Please refer to Chapter 3.2.2.10 of the user manual for further settings.

JT1(TX signal), JR1(RX signal): COM3 RS-422/485 termination resistor
Closed Pins	Result
1-2	Disable termination
2-3	*Enable termination
* Default

JFV1: VGA dummy load setting
Closed Pins	Result
1-2	Disable termination
2-3	*Enable termination
* Default

Declaration of Conformity

This device complies with the requirements in Part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.
Caution! The computer is supplied with a battery-powered real-time clock circuit. There is a danger of explosion if the battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.