Loading manuals...

onn 2 Channel Soundbar User Guide


The onn 2 Channel Soundbar User Guide is a great way to get the most out of your soundbar. This guide will show you how to set up and use your soundbar, as well as answer any questions you might have about it.

 inserts For Fcc Id

  1. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  2. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
    However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.
  3. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
    1. this device may not cause harmful interference, and
    2. this device must accept any interference received, including interference that may cause undesired operation.
  4. RF Exposure Statement
    To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Package Contents

  1. Soundbar 1pc
  2. 3.5mm audio to RCA audio cable (Length: 1.5m) 1pc
  3. Remote control 1pc
  4. Product Guide 1pc
  5. External adaptor 1pc

Diagram showing package contents

Speaker Overview

  1. Status indicator
  2. Wall mount
  3. Aux in
  4. Optical
  5. Power
  6. Power on / off
  7. Source
  8. Volume down
  9. Volume up

Front of the soundbar view
Rear of the soundbar view
Top-down view of soundbar

Status Indicator

Standby Solid Red
Optical Solid Green
Aux in Solid White
Bluetooth pairing mode Flashing blue
Bluetooth device connected Solid blue
Volume up and down Corresponding to the sound source indicator light flash 1 time
Maximum and minimum volume Corresponding to the sound source indicator light flash 3 times
Mute Slow flash
TV mode Corresponding to the sound source indicator light flash 2 times

(adsbygoogle = window.adsbygoogle || []).push({});

Music mode Corresponding to the sound source indicator light flash 2 times
Movie mode Corresponding to the sound source indicator light flash 2 times

Specifications

  • Output Power: 12.5W x 2(RMS)
  • Frequency Response: 50Hz~20 KHz
  • S/N Ratio: ≥65dB
  • Separation: ≥45dB

Remote Control

Diagram showing the buttons on the remote control

  1. Power on off
  2. Mute
  3. Bluetooth
  4. Aux
  5. Optical
  6. TV mode
  7. Music mode
  8. Movie mode
  9. Volume up
  10. Previous track
  11. Play / Pause
  12. Next track
  13. Volume down

Remote Control Batteries

Before First Use

To prepare the remote control for first use, pull out the safety strip to activate the battery.
Pull the tab to engage the batteries included with the remote control

Replacing The Battery

When replacing the battery in the remote control, refer to the diagram below.

Diagram showing how to replace the battery in the remote control

  1. Press the catch across.
  2. While holding the catch, open the battery door.
  3. Fit the battery observing polarity as shown. When replacing the battery, use only the same CR2025 type specified.

Inserting the battery the right way up

Power And Connection

  1. Plug the DC cable from the AC adaptor into the Power jack on the back panel, and plug the AC adaptor into the wall socket.
  2. Press Power icon to power on/power off.
  3. Connect the audio cable to the audio output of any device (such Desktop PC, Laptop, Smartphone Tablet, MP3, TV etc.)with a 3.5 mm headphone output jack or RCA output jack.

Diagram showing the power cord plugged into the rear
Plugging the soundbar into a TV
Cable not included diagram
Diagram showing what the soundbar can be plugged into

Bluetooth® Connection

  1. Turn on the soundbar and select the Bluetooth® mode.
  2. Activate the Bluetooth® function on your device and search for devices nearby.
  3. Find “Onn 16” Soundbar” in the search results and tap to connect.
  4. The Bluetooth® indicator will turn solid blue on a successful connection.

Notes

  • The Bluetooth indicator will keep flashing when the soundbar is pairing.
  • Please make sure no other active Bluetooth® devices are within range, and that the soundbar is within 3ft / 1m away from your device.
  • Before starting to play via Bluetooth, please lower the volume to a moderate level.
onn 2 Channel Soundbar User Guide Image

Manufactured by Onn

(all Onn manuals)



More Manuals From Onn